Initial commit

2026-02-23 20:42:11 -07:00
commit 2ba96a115d
462 changed files with 9166588 additions and 0 deletions
--- a/verilog/dv/wb_port/wb_port.c
+++ b/verilog/dv/wb_port/wb_port.c
@@ -0,0 +1,90 @@
+/*
+ * SPDX-FileCopyrightText: 2020 Efabless Corporation
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+// This include is relative to $CARAVEL_PATH (see Makefile)
+#include <defs.h>
+#include <stub.c>
+
+#define reg_mprj_slave (*(volatile uint32_t*)0x30000000)
+
+/*
+	Wishbone Test:
+		- Configures MPRJ lower 8-IO pins as outputs
+		- Checks counter value through the wishbone port
+*/
+
+void main()
+{
+
+	/* 
+	IO Control Registers
+	| DM     | VTRIP | SLOW  | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
+	| 3-bits | 1-bit | 1-bit | 1-bit  | 1-bit  | 1-bit | 1-bit   | 1-bit   | 1-bit | 1-bit | 1-bit   |
+	Output: 0000_0110_0000_1110  (0x1808) = GPIO_MODE_USER_STD_OUTPUT
+	| DM     | VTRIP | SLOW  | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
+	| 110    | 0     | 0     | 0      | 0      | 0     | 0       | 1       | 0     | 0     | 0       |
+	
+	 
+	Input: 0000_0001_0000_1111 (0x0402) = GPIO_MODE_USER_STD_INPUT_NOPULL
+	| DM     | VTRIP | SLOW  | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
+	| 001    | 0     | 0     | 0      | 0      | 0     | 0       | 0       | 0     | 1     | 0       |
+	*/
+
+	/* Set up the housekeeping SPI to be connected internally so	*/
+	/* that external pin changes don't affect it.			*/
+
+    reg_spi_enable = 1;
+    reg_wb_enable = 1;
+	// reg_spimaster_config = 0xa002;	// Enable, prescaler = 2,
+                                        // connect to housekeeping SPI
+
+	// Connect the housekeeping SPI to the SPI master
+	// so that the CSB line is not left floating.  This allows
+	// all of the GPIO pins to be used for user functions.
+
+    reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_23 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_22 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_21 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_20 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_19 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_18 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
+    reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;
+
+     /* Apply configuration */
+    reg_mprj_xfer = 1;
+    while (reg_mprj_xfer == 1);
+
+	reg_la2_oenb = reg_la2_iena = 0x00000000;    // [95:64]
+
+    // Flag start of the test
+	reg_mprj_datal = 0xAB600000;
+
+    reg_mprj_slave = 0x00002710;
+    reg_mprj_datal = 0xAB610000;
+    if (reg_mprj_slave == 0x2B3D) {
+        reg_mprj_datal = 0xAB610000;
+    }
+}